充气类产品FLOAT PRODUCTS检验大体标准 免费送

純爺們→軍

外观：不能有补丁,熔接处要光滑，不能有锐角锐边。
功能测试：依据产品类型，首先确认工厂针对漏气是否是全检项目，因产品大小不同会有12-24小时的保压测试，检验时请确认工厂是否以此执行。
到工厂核对麦头确认是我司出货产品后，先抽检测试之产品做功能及充气测试，以便有足够的时间确定产品是否有漏气现象。
针对体积比较小的充气产品，充气后将产品置于水中，检查是否有漏气现象；
针对体积大的可用一定浓度的肥皂水，用手涂抹产品本体，察看是否有气泡产生。
功能性测试：冲击测试，静载测试，按照产品的实际用途，在大于产品实际承受重量1.5倍下静载。
例如:充气床冲击重量150kgs 高度30-50cm, 静载重量250kgs.

woowhoow

学习一下，世界太大，我等要多多学习啊

sailing220

好东西，学习了

alanjiang_8888

请问这位高手像充气的球类该怎么测试和检验足球？
能否发一份给alanjiang_8888@126.com感激不尽。

huggins_tang

好东西，顶下

dannywu

4.1 Performance Tests

   4.1.1 Mattress Pressure / Leak Test: (Inflatable Bed)

  The mattress will be fully inflated to a pressure of 12.9 mm Hg (6.9 in H2O). A sheet of 1.2 m x 45.7 cm x 1.9 cm (4.0 ft x 1.5 ft x 0.75 in) board will be centered on the mattress. Three (3) 22.7 kg (50 lb) weights will be distributed on the board.

After 24 hours, the mattress pressure will be no less than 5.2 mm Hg (2.8 in H2O).


   4.1.2 Weld Failure Test: (Inflatable Bed)

  The mattress will be inflated to a pressure of no less than 67 mm Hg (36 in H2O) without weld or valve failure.


   4.1.3 Static Load Test (Twin): (Inflatable Bed)

  Inflate each chamber of the mattress to a pressure of 15 in H2O. A sheet of 1.2 m x 45.7 cm x 1.9 cm (4.0 ft x 1.5 ft x 0.75 in) board will be centered on the mattress. Weight totalling 147.4 kg (325 lb) will be distributed on the board.
After 1 hour, there will be no leaks.


   4.1.4 Set A Load Test (Twin): (Inflatable Bed)

  Inflate each chamber of the mattress to a pressure of 15 in H2O.
A sheet of 1.2 m x 45.7 cm x 1.9 cm (4.0 ft x 1.5 ft x 0.75 in) board will be centered on the mattress. Weight totalling 147.4 kg (325 lb) will be distributed on the board. Suspend the weighted board 2.5 cm (1 in) above the mattress.
The weighted board will be dropped onto the mattress 4500 times at an appropriate rate of between 5 and 40 cycles per minute constantly maintaining 2.5 cm (1.0 in) above the mattress.
At end of test, there will be no leaks.


   4.1.5 Drop Test w/ Weight (Twin): (Inflatable Bed)

  Inflate each chamber of the mattress to a pressure of 15 in H2O.
A sheet of 1.2 m x 45.7 cm x 1.9 cm (4.0 ft x 1.5 ft x 0.75 in) board will be centered on the mattress. Weight totalling 147.4 kg (325 lb) will be distributed on the board. Suspend the weighted board 15.2 cm (6 in) above the mattress.
The weighted board will be dropped onto the mattress 6 times constantly maintaining 15.2 cm (6.0 in) above the mattress.
At end of test, there will be no leaks.

純爺們→軍

呵呵  抛砖引玉  来了好多高手啊             谢谢大家评点啊  学习了!

smith

thanks a lot

hing

学习了

紫色梦幻

朋友!你问的是橡胶类的充气球?还是一次注塑充气的健身球?我们公司只做PVC塑胶类的充气玩具产品类?