验货员论坛

标题: 自己总结的一些外企验货公司可能问到的一些问题，无私奉献！回答自己写的。 [打印本页]

作者: myqcsister 时间: 2011-12-27 14:04
标题: 自己总结的一些外企验货公司可能问到的一些问题，无私奉献！回答自己写的。
1, What’s inspection standard and method  are normally employed for the inspection of a softline item (e.g. garment, bag,shoes, etc.)? what is the standard carton sampling method (how to determine the  no. of cartons for inspection)?

A: Normally employed standard for softline  item is final random inspection per ANSI/ASQ-1.4, single sampling plan, inspection level GII, AQL for critical is 0, major 2.5, minor 4.0.
Selected carton quantity is greater or equal  square root of total cartons number (then round the number up). If the required carton number of samples can not be met, select more cartons until the requirements are fulfilled.

2, Describe briefly the basic steps in the inspection standard.

A: 1, Check shipment quantity, PO NO. &style NO., selected cartons randomly; 2,check packing and shipping mark; 3,product conformity checking; 4, on site test checking, included barcode scan test, metal detect test, accessory function checking, stuffing material screening and so on. 5, measurement checking; 6, workmanship checking; finally report.

3, Describe briefly the application of single/double sampling plan for an inspection?

A: For single sampling plan, sampling only 1 time should be done,  if defective samples quantity beyond AQL, fail workmanship; if defective samples quantity within AQL, pass this part. For double sampling plan, if the 1st sampling’s result between acceptable and refused,  the 2nd sampling should be done. For the very good or bad bulks, double sampling plan can save inspection times and cost.

4, How many inspection levels are classified in the AQL system? How is the application of each level?

A: 7 levels are classified in the AQL system, special inspection levels: S-1, S-2, S-3 &
S-4. General inspection levels: LI,LII ＆ LIII. From S-1 to LIII, selected sample size was from the least to the most. For special levels, adopt in high cost, damaged, long time check or test. For general levels, adopt in workmanship inspection normally.

5, Describe how you define the term defect?And how to judge a critical, major or minor defect.

A: Defect is the difference between actual findings and the criteria. Classification of defect as below:
A critical defect is likely to result in hazardous or unsafe condition for an individual using the product or that is contravening against the mandatory regulations.
A major defect is likely in failure reducing the usability, value of the products and obvious appearance defects affecting the salability of the products.
A minor defect that doesn’t reduce the usability of the product, but nevertheless the workmanship is beyond the defined quality.

6, What information is generally included in a wash/care label? Please explain briefly.

A: Composition, washing method instruction,care symbols, supplier’s information and maybe included PO no., item  no., and so on.

7, What are the possible outcomes of an inspection?
A: Inspection result: Fail: we found anypoint different from the related mandatory standard or client’s requirement.Pass: all the findings are conformed to the related mandatory standard and client’s requirement.
Pending: pending is an interim result, this result will be transfer to pass or fail by the client after reviewing all the findings.

8, List 6 fabric defects (3 knits and 3wovens).

A: Knits: laddering, pull out loops, knot;
Wovens: foreign yarn, coarse yarn, fabric torn.

9, List 5 shoes defects.

A: Frayed edge, ankle strap too short, bubble at insole, poor bonding, shank not straight.

10, List 5 sewing defects.

A: Run off stitches, broken stitches, messy stitches, loose stitches, skipped stitches.

11, List 3 leather defects.

A: Broken grain, marbled grain, mildews.

12, During an inspection, a factory representative tells you the client has accepted some kind of non-conformities,What should you do?

A: Ask factory representative to provide anattestation to prove this. Just like client’s E-mail. If provide, ignore those non-conformities and remark into report. If he couldn’t provide this, count as non-conformity and fail the report.

13, Would you accept any transportation/ meal arrangements by the factory party? Why?

A: Normally I don’t accept any transportation/ meal arrangements from the factory because inspection should be entirely without any prejudice.

14, Describe how you define to be a good QCinspector.

A: He must be an honest man first. Inspects bulks with chariness and equity. Be affluent in inspection experience and begood at communication. Work hard and comply with corporation’s regulations.

作者: 吴治钢 时间: 2011-12-27 14:14

Describe how you define to be a good QCi

作者: worldlink 时间: 2011-12-27 14:31
很好,很强大,很热心.

作者: 好好学习2 时间: 2011-12-27 14:56
支持！

作者: 262032327 时间: 2011-12-27 16:24

作者: myqcsister 时间: 2011-12-27 18:56
标题: 回复 3# worldlink 的帖子
谢谢。我希望我的一些帖子能给需要帮助的朋友一些启发。我不想用附件要金币的方式，因为那样会有些没有注册或者金币少的朋友无法看到。要分享，就大家都可以看到。如果有什么需要解答的，我帮助大家。当年我想学习一些验货的资料的时候，很多资料都是要金币或者权限的，所以十分反感那种方式。。。。

作者: dawink 时间: 2011-12-27 20:24
支持LZ，希望看到更多经验分享。

作者: szcougar 时间: 2011-12-27 20:57
不错谢谢分享！！1

作者: emus 时间: 2011-12-27 21:57
好人发大财！

作者: Denny.Xie 时间: 2011-12-28 07:59
are you a HR manager ? hehe

作者: cunliang1213 时间: 2011-12-28 08:26
标题: 回复 1# myqcsister 的帖子
好啊，经验谈~~~~~~~~

作者: sunday-hu 时间: 2011-12-28 11:27

作者: weideqiang 时间: 2011-12-28 14:39
Thank you for you shared

作者: hung 时间: 2011-12-28 15:16
Thank you for your sharing!!!!!!!!!!!

作者: myqcsister 时间: 2011-12-28 15:44
标题: 回复 9# emus 的帖子
谢谢，大家一起发财！呵呵

作者: myqcsister 时间: 2011-12-28 15:45
标题: 回复 13# weideqiang 的帖子
不客气，大家共同分享，一起发财。

作者: myqcsister 时间: 2011-12-28 15:46
标题: 回复 14# hung 的帖子
不客气。兄弟的头像v5！呵呵

作者: myqcsister 时间: 2011-12-28 15:47
标题: 回复 10# Denny.Xie 的帖子
不是啊，我也是一个验货员。面试了几次，就总结了一些问题，回到家自己把答案推敲推敲了一番。呵呵

作者: huanggeng 时间: 2011-12-28 18:03

谢谢LZ，很好的帖子！

作者: ruth.zeng 时间: 2011-12-28 18:15
你是一个好人。。。

作者: myqcsister 时间: 2011-12-28 20:53
标题: 回复 20# ruth.zeng 的帖子
很多女孩子都这么说。
当他们这么说的时候，
我就知道我又没戏了。。。。。

作者: dawink 时间: 2011-12-28 21:43

原帖由 myqcsister 于 2011-12-28 20:53 发表
很多女孩子都这么说。
当他们这么说的时候，
我就知道我又没戏了。。。。。

hehe

作者: worldlink 时间: 2011-12-29 11:36
LZ在公正行上班吗!目前在哪个地区!

作者: myqcsister 时间: 2011-12-29 11:40
标题: 回复 23# worldlink 的帖子
在华东地区哦。

作者: huanggeng 时间: 2011-12-29 14:17
再顶一次.............

作者: lakezhao 时间: 2011-12-29 15:15
selected cartons randomly
我觉得select 这里该用draw

作者: lakezhao 时间: 2011-12-29 15:20
很不错的帖子，也叫专业。

作者: myqcsister 时间: 2011-12-29 15:45
标题: 回复 26# lakezhao 的帖子
谢谢。。selected 和 draw 可能每个公司的叫法不太一样啊。不过应该都是OK的。

作者: mysister 时间: 2011-12-29 19:41
大哥你是牛人，谢谢你的分享论坛有你们才发展这么好牛

作者: mysister 时间: 2011-12-29 19:42
我发现我们的名字就差个QC 有缘啊不知道能跟你私下交流不

作者: myqcsister 时间: 2011-12-29 20:09
标题: 回复 30# mysister 的帖子
呵呵，是比较有缘哦。你想交流哪些方面的，可以给我发邮件哦，goodinspector@163.com

作者: myqcsister 时间: 2011-12-29 20:10
标题: 回复 25# huanggeng 的帖子
你都顶得我受不了啦~~~

作者: yczj0723 时间: 2011-12-30 18:37
thanks for sharing

作者: rli 时间: 2011-12-30 19:59
Thanks for sharing!

作者: myqcsister 时间: 2011-12-31 16:42

原帖由 yczj0723 于 2011-12-30 18:37 发表
thanks for sharing

不用客气，大家共同进步。。。。

作者: myqcsister 时间: 2011-12-31 16:45

原帖由 rli 于 2011-12-30 19:59 发表
Thanks for sharing!

不用客气，共同进步

作者: riceorange 时间: 2012-1-1 22:52
good person!

作者: myqcsister 时间: 2012-1-4 17:14

祝大家新年好。。。。。

作者: a604b 时间: 2012-1-4 21:48
无能为力啊，英语不行呢！

作者: myqcsister 时间: 2012-1-6 15:43

原帖由 a604b 于 2012-1-4 21:48 发表
无能为力啊，英语不行呢！

我英语基础也不好，都是边工作边学习的。

作者: kenjilau 时间: 2012-1-6 16:06
收藏，感谢！

作者: worldlink 时间: 2012-1-17 17:32
应该加精!

作者: MS168 时间: 2012-1-17 17:59
are you a HR manager ? hehe

作者: 向验货进军 时间: 2012-1-21 23:52

原帖由 myqcsister 于 2011-12-27 18:56 发表
谢谢。我希望我的一些帖子能给需要帮助的朋友一些启发。我不想用附件要金币的方式，因为那样会有些没有注册或者金币少的朋友无法看到。要分享，就大家都可以看到。如果有什么需要解答的，我帮助大家。当年我想学习一 ...

楼主说的真好，本想发树大拇指的表情，可惜没找到。谢谢楼主

作者: frankwang1 时间: 2012-1-22 13:49
真是好贴啊

作者: 水准仪 时间: 2012-2-3 11:17
thank for your sharing

作者: sn823 时间: 2012-2-3 18:08

,Can you provide more defective description.

作者: caojiake88 时间: 2012-2-3 21:07

THANKS FOR YOUR SHARING,I THINK I SHOULD LEARN ENGLISH MORE FREQUENCYLY.

作者: daiyan1228 时间: 2013-9-27 11:23
非常感谢

作者: 超越自我 时间: 2014-7-29 08:01
谢谢分享

作者: 验货-1 时间: 2014-7-29 10:12
谢谢

作者: 超越自我 时间: 2014-7-30 06:32
谢谢分享

欢迎光临验货员论坛 (http://bbs.wtoqc.net/)