模具专业英語 - 验货员论坛

入水：gate       进入位：　gate location       水口形式：gate type    大水口：edge gate
细水口： pin-point gate    水口大小：gate size    转水口：　switching runner/gate
唧嘴口径：　sprue diameter
??
二、流道: runner
??热流道：　hot runner,hot manifold       热嘴冷流道: hot sprue/cold runner
??唧嘴直流: direct sprue gate                圆形流道：round(full/half runner
??流道电脑分析：mold flow analysis          流道平衡:runner balance
??热嘴：　hot sprue                               热流道板：hot manifold
??发热管：cartridge heater                      探针: thermocouples
??插头：　connector plug                         插座： connector socket
??密封/封料： seal
??
三、运水：water line                         喉塞：line lpug
喉管：tube
   塑胶管：plastic tube                   快速接头：jiffy quick connector
plug/socker
??
四、模具零件：　mold components

??三板模：3-plate mold                         二板模：2-plate mold
??边钉/导边：leader pin/guide pin          边司/导套：bushing/guide bushing
??中托司：shoulder guide bushing          中托边L：guide pin
??顶针板：ejector retainner plate          托板：　support plate
??螺丝： screw                                     管钉：dowel pin
??开模槽：ply bar scot                            内模管位：core/cavity inter-lock
??顶针：　ejector pin                            司筒：ejector sleeve
??司筒针：ejector pin                            推板：stripper plate
??缩呵：movable core,return core core puller
??扣机（尼龙拉勾）：nylon latch lock       斜顶：lifter
??模胚（架）： mold base                      上内模：cavity insert
??下内模：core insert                            行位（滑块）： slide
??镶件：insert                                     压座/斜鸡：wedge
??耐磨板/油板：wedge wear plate       压条：plate
??撑头: support pillar                            唧嘴： sprue bushing
??挡板：stop plate                               定位圈：locating ring
??锁扣：latch                                        扣鸡：parting lock set
??推杆：push bar                                  栓打螺丝：S.H.S.B
??顶板：eracuretun                               活动臂：lever arm
??分流锥：spure sperader                   水口司:bush
??垃圾钉：stop pin                               隔片：buffle
??弹弓柱：spring rod                            弹弓:die spring
??中托司：ejector guide bush             中托边：ejector guide pin
??镶针：pin                                        销子：dowel pin
??波子弹弓：ball catch
??
模具成形不良用语英汉对照

aberration 色差 atomization ?化                bank mark ?料纹 bite 咬入
blacking hole 涂料孔(铸疵)                            blacking scab 涂料疤
blister 起泡          blooming 起霜       low hole 破孔          blushing 泛白
body wrinkle 侧壁皱纹                                  breaking-in 冒口带肉
bubble 膜泡       burn mark 糊斑       burr 毛边                camber 翘曲
cell 气泡             center buckle 表面中部波皱       check 细裂痕
checking 龟裂
chipping 修整表面缺陷                                  clamp-off 铸件凹痕
collapse 塌陷 color mottle 色斑
corrosion 腐蚀 crack 裂痕
crazing 碎裂 crazing 龟裂
deformation 变形 edge 切边碎片
edge crack 裂边 fading 退色
filler speak 填充料斑 fissure 裂纹
flange wrinkle 凸缘起皱 flaw 刮伤
flow mark 流痕 galling 毛边
glazing 光滑 gloss 光泽
grease pits 污斑 grinding defect 磨痕
haircrack 发裂 haze 雾度
incrustation 水锈 indentation 压痕
internal porosity 内部气孔 mismatch 偏模
mottle 斑点 necking 缩颈
nick 割痕 orange peel 橘皮状表面缺陷
overflow 溢流 peeling 剥离
pit 坑 pitting corrosion 点状腐蚀
plate mark 模板印痕 pock 麻点
pock mark 痘斑 resin streak 树脂流纹
resin wear 树脂脱落 riding 凹陷
sagging 松垂 saponification 皂化
scar 疤痕 scrap 废料
scrap jam 废料阻塞 scratch 刮伤/划痕
scuffing 深冲表面划伤 seam 裂痕
shock line 模口挤痕 short shot 充填不足
shrinkage pool 凹孔 sink mark 凹痕
skin inclusion 表皮折叠 straightening 矫直
streak 条状痕 surface check 表面裂痕
surface roughening 橘皮状表皮皱折 surging 波动
sweat out 冒汗 torsion 扭曲
warpage 翘曲 waviness 波痕
webbing 熔塌 weld mark 焊痕
whitening 白化 wrinkle 皱纹