作者: Kenny.li 时间: 2010-8-29 14:12
路过 。。。。。。作者: kevin_6888 时间: 2010-8-30 15:20
支持一下LZ作者: 冰绿茶 时间: 2010-8-30 16:06
呵呵呵。。。。。。作者: uphui 时间: 2010-8-30 18:07
嗯 ,不错,谢谢楼主分享。作者: 冰红茶 时间: 2010-8-30 19:35
有没有中文的呀,下载了看不懂作者: goodscott 时间: 2010-9-7 17:12
路过,TKS,LZ作者: fxy104 时间: 2010-9-8 14:30
路过的,谢谢分享作者: Evan.hu 时间: 2010-9-8 21:28
是数码相框的WM作者: 特级QC 时间: 2010-9-20 15:05
路过ing...作者: LYS1012 时间: 2010-9-20 22:46
是中文的还是英文的?作者: billlee 时间: 2010-9-24 00:11
先支持一下了....作者: zaptiah 时间: 2010-9-24 09:06
我顶!!!!!作者: bakker 时间: 2010-9-29 09:39
UP 楼主~~~~作者: fxy104 时间: 2010-10-20 15:20
支持你一下,,,作者: LYS1012 时间: 2010-11-5 22:17
英文的就不用了,下了也看不懂作者: Phenix 时间: 2010-12-14 15:03
很好,支持一下作者: 质标检测 时间: 2015-12-2 02:39
Inspection procedure and checklist for Digital Photo Viewer
1. Scope:
To provide the general requirements definitions for Final Random Inspection to
Digital Photo Viewer
2. Sampling plan adopted
ANSI/ASQC-Z1.4 / BS 6001.1.1999/ ISO 2859-1 date 1999
Single sampling plan for normal inspection general inspection level II
Acceptance Quality Level (AQL) (Recommended)
Critical defective: Not allowed on the inspected samples
Major Nonconformity (defective): 1.0
Minor Nonconformity (defective): 4.0
For combined inspection, the sampling of each model depends on the percentage of the
model in the batch. At least take 1 sample per model for checking, for the inspection plan is
Special Inspection level or Fixed sample size.
3. General defect classification:
3.1 Critical Nonconformity (Defect) -
Not Allowed for inspected samples
A defect which experience and judgment indicates is likely to result to result in a
hazardous and / or injurious situation to the user, or makes the product subject to
governmental seizure.
3.2 Major Nonconformity (Defect) – provided by client
Any unit having a nonconformity (defect) other than critical is likely to result in
failure, or to reduce materially the usability of the unit for its intended purpose, or
any unit having an aesthetics nonconformity (defect) which affect the saleability
of the products, or as per applicant’s requirement.
3.3 Minor Nonconformity (Defect) – provided by client
Any unit having a nonconformity (defect) that in not likely to reduce the usability of
the unit for its intended purpose, or is departure from established standards having
little bearing on the effective use of the products.
3.4 Other Nonconformity Defect
The following described are those most commonly found, but not necessarily cover
all possible nonconformity (defects). Any other functional or visual nonconformity
(defect) shall be initially classified according to the above mentioned p作者: hanyanchuang 时间: 2016-3-9 10:37
谢谢作者: mjj10 时间: 2016-3-14 17:09
赶紧下下来看看作者: wei20054860 时间: 2016-3-15 00:29
看看先作者: sg2199 时间: 2016-4-9 15:35
飘过。。。作者: sam510xie 时间: 2016-4-13 20:31
路过,谢谢分享!作者: 15888912034 时间: 2016-4-16 22:44