验货员论坛

标题: 充气类产品FLOAT PRODUCTS检验大体标准 免费送 [打印本页]

作者: 純爺們→軍    时间: 2008-1-22 11:51
标题: 充气类产品FLOAT PRODUCTS检验大体标准 免费送
外观:不能有补丁,熔接处要光滑,不能有锐角锐边。
功能测试:依据产品类型,首先确认工厂针对漏气是否是全检项目,因产品大小不同会有12-24小时的保压测试,检验时请确认工厂是否以此执行。
到工厂核对麦头确认是我司出货产品后,先抽检测试之产品做功能及充气测试,以便有足够的时间确定产品是否有漏气现象。
针对体积比较小的充气产品,充气后将产品置于水中,检查是否有漏气现象;
针对体积大的可用一定浓度的肥皂水,用手涂抹产品本体,察看是否有气泡产生。
功能性测试:冲击测试,静载测试,按照产品的实际用途,在大于产品实际承受重量1.5倍下静载。
例如:充气床冲击重量150kgs 高度30-50cm, 静载重量250kgs.

作者: JAKEY    时间: 2008-1-23 09:39
楼主的建议不错.....顶一下...
作者: qingqingh    时间: 2008-4-9 10:24
是好東西,頂一下
作者: HoCheung    时间: 2008-4-9 13:30
up......
作者: lijiatu    时间: 2008-4-10 16:27
.............................
作者: ankyo200    时间: 2008-4-10 21:04
thanks ,have a look
作者: 紫色梦幻    时间: 2008-4-10 21:39
标题: 回复 #1 純爺們→軍 的帖子
针对体积大的可用一定浓度的肥皂水,用手涂抹产品本体,察看是否有气泡产生。

肥皂水不能涂抹在PVC产品上。除非被涂产品将报废。用清水测试后都必须立即擦净,否则,会出现斑痕。再说有的植绒产品更不能打湿。
我从事吹气玩具检验14年,原在深圳后在广东中山最大的一家。05年到上海。有做吹气玩具的或验吹气玩具的朋友,
愿意交流的可联系我。
QQ569289302
作者: guofang410    时间: 2008-4-20 18:30
好东西啊,我顶,谢谢楼主了啊
作者: 余兴军    时间: 2008-4-21 14:39
好东西,我顶一下!!!!!!!!!
作者: melodyhata200    时间: 2008-4-22 18:08
原帖由 紫色梦幻 于 2008-4-10 21:39 发表
针对体积大的可用一定浓度的肥皂水,用手涂抹产品本体,察看是否有气泡产生。

肥皂水不能涂抹在PVC产品上。除非被涂产品将报废。用清水测试后都必须立即擦净,否则,会出现斑痕。再说有的植绒产品更不能打湿 ...


封接边作拉力测试不合格的.有什么方法来加强呢?
充气水上玩具除了不可漏气外.还有什么要注意的呢?
什么情况下有些地方要独立充气不可一体化充气...?
起到一些模拟功能(楼梯,扶手等)的部件受到外力时完全变形了.这属于DEFECTS吗?
作者: wwnw_007    时间: 2008-4-27 12:43
learn new goods!!!THK everyone!!!
作者: 紫色梦幻    时间: 2008-4-29 16:25
标题: 回复 #10 melodyhata200 的帖子
朋友:
    我回复到你的邮箱了,你收到了吗?
    我现在再发一次.
作者: rachel5201314    时间: 2008-5-4 21:36
顶一下!!!!!!!!!!!
作者: erictao    时间: 2008-5-6 08:52
very good!
作者: wwnw_007    时间: 2008-5-6 09:42
supporting!!!
作者: super    时间: 2008-5-6 11:53
标题: 回复 #7 紫色梦幻 的帖子
请问这位高手像充气的球类该怎么测试<比如篮球,足球,排球等>
能否发一份给我chenliang0030@163.com感激不尽。
作者: 紫色梦幻    时间: 2008-5-9 13:43
标题: 回复 #16 super 的帖子
朋友!你问的是橡胶类的充气球?还是一次注塑充气的健身球?我们公司只做PVC塑胶类的充气玩具产品类?
作者: hing    时间: 2008-10-25 20:01
学习了
作者: smith    时间: 2008-10-31 15:10
thanks a lot
作者: 純爺們→軍    时间: 2008-11-13 12:50
呵呵  抛砖引玉  来了好多高手啊             谢谢大家评点啊  学习了!
作者: dannywu    时间: 2008-11-14 15:40
标题: 我公司是这样的,
4.1 Performance Tests

   4.1.1 Mattress Pressure / Leak Test: (Inflatable Bed)

  The mattress will be fully inflated to a pressure of 12.9 mm Hg (6.9 in H2O). A sheet of 1.2 m x 45.7 cm x 1.9 cm (4.0 ft x 1.5 ft x 0.75 in) board will be centered on the mattress. Three (3) 22.7 kg (50 lb) weights will be distributed on the board.

After 24 hours, the mattress pressure will be no less than 5.2 mm Hg (2.8 in H2O).


   4.1.2 Weld Failure Test: (Inflatable Bed)

  The mattress will be inflated to a pressure of no less than 67 mm Hg (36 in H2O) without weld or valve failure.


   4.1.3 Static Load Test (Twin): (Inflatable Bed)

  Inflate each chamber of the mattress to a pressure of 15 in H2O. A sheet of 1.2 m x 45.7 cm x 1.9 cm (4.0 ft x 1.5 ft x 0.75 in) board will be centered on the mattress. Weight totalling 147.4 kg (325 lb) will be distributed on the board.
After 1 hour, there will be no leaks.


   4.1.4 Set A Load Test (Twin): (Inflatable Bed)

  Inflate each chamber of the mattress to a pressure of 15 in H2O.
A sheet of 1.2 m x 45.7 cm x 1.9 cm (4.0 ft x 1.5 ft x 0.75 in) board will be centered on the mattress. Weight totalling 147.4 kg (325 lb) will be distributed on the board. Suspend the weighted board 2.5 cm (1 in) above the mattress.
The weighted board will be dropped onto the mattress 4500 times at an appropriate rate of between 5 and 40 cycles per minute constantly maintaining 2.5 cm (1.0 in) above the mattress.
At end of test, there will be no leaks.


   4.1.5 Drop Test w/ Weight (Twin): (Inflatable Bed)

  Inflate each chamber of the mattress to a pressure of 15 in H2O.
A sheet of 1.2 m x 45.7 cm x 1.9 cm (4.0 ft x 1.5 ft x 0.75 in) board will be centered on the mattress. Weight totalling 147.4 kg (325 lb) will be distributed on the board. Suspend the weighted board 15.2 cm (6 in) above the mattress.
The weighted board will be dropped onto the mattress 6 times constantly maintaining 15.2 cm (6.0 in) above the mattress.
At end of test, there will be no leaks.
作者: huggins_tang    时间: 2008-11-14 18:46
好东西,顶下
作者: alanjiang_8888    时间: 2010-4-20 13:03
请问这位高手像充气的球类该怎么测试和检验足球?
能否发一份给alanjiang_8888@126.com感激不尽。
作者: sailing220    时间: 2010-4-20 21:53
好东西,学习了
作者: woowhoow    时间: 2010-4-27 10:30
学习一下,世界太大,我等要多多学习啊




欢迎光临 验货员论坛 (http://bbs.wtoqc.net/) Powered by Discuz! X3.2