验货员论坛

标题: How to control the un-expected thing occus during the inspection? [打印本页]

作者: kenjilau 时间: 2007-11-19 10:34
标题: How to control the un-expected thing occus during the inspection?
Do we report everything/feedback to our company, when some un-expected matter occurs ?
Say, the shippming marks was wrong.....and we have to report this, right?

P.S. I cant type in chinese, as the notebook dont support chinese input.

作者: lcq399 时间: 2007-11-19 12:44
看来你真是一个初级的验货员啊,唛头错误当然要报告了,就是不FAIL,那REMARK里一定要写上的!不然就是你业务的问题了!网上到处是五笔,你就不能下载一个,电脑水平要提高啊!

作者: calin0923 时间: 2007-11-19 14:00
If I do the final inspection, I will just accept or reject the goods with the inspection report. If I do
in-line inspection, I will ask factory to correct the defects and give a detailed correction report. Inspection items depend on the engineer's IP(inspection protocol) .

作者: kenjilau 时间: 2007-11-19 14:13

原帖由 lcq399 于 2007-11-19 12:44 发表
看来你真是一个初级的验货员啊,唛头错误当然要报告了,就是不FAIL,那REMARK里一定要写上的!不然就是你业务的问题了!网上到处是五笔,你就不能下载一个,电脑水平要提高啊!

thanks your reply and comments. As for the chinese typing, as the boss not allow me to use the laptop for non-business usage. he not allow me to use chinese inputing in this notebook.

作者: HoCheung 时间: 2007-11-20 11:08
that depends on your company, for most enterprises that belongs to HK, you must report to them and only they can make a decision about acceptance or rejection. If you reported USA or other oversea supersiors, they may consign the rights to you, you just report them about the result. For the wrong shipping mark, as usual, you should report your supervisor and ask the vendor to correct!

作者: HoCheung 时间: 2007-11-20 11:19
Plug, here just provided you a perfect condition to practise your English, if you can use English, why not? whoever will not blame you for what you say is right or not. you can use Chinese once in while. no one will laugh at you. Just try! Don't forget our purpose, to advance together!

作者: kenjilau 时间: 2007-11-20 13:06

原帖由 HoCheung 于 2007-11-20 11:08 发表
that depends on your company, for most enterprises that belongs to HK, you must report to them and only they can make a decision about acceptance or rejection. If you reported USA or other overse ...

thanks your comments. and my company is a italia company and has a HK office, my core task just to check up the goods' quality and report to the HK office.....

作者: catfly18 时间: 2007-11-23 10:29
标题: 回复 #1 kenjilau 的帖子
Easy.
First, you must know you will assume full responsibility for the packing after inspection.
so, when you find packing mistake, you should let factory to correct it at once.
you needn't report to your leader.
But if the factory is unwilling to improve. Or, it is no time to correct for catching a shipment, you should report to your final decision maker. If you obtain a authorization to let the bulk
release with packing mistake. so you should write this issue in your report. And write formal
email to all related staff as a note.

作者: fanyejian 时间: 2007-11-23 19:55
I don't think so,cause ,we are all chinese ,so sometime for example,if the rsik you take is under your control,just do it ,there is nothing big deal,experience make you perfect,so if you help the factory,they will help you ,if the shipping mark was wrong,just remake it,it only need a little time,so this method is win-win to both you and the supplier

作者: LZQ@0223 时间: 2007-12-5 15:54

作者: harline 时间: 2007-12-16 22:36

作者: stephen981 时间: 2007-12-28 11:42
you are all right,but i think we will to see what number of the carton ,if the number is very small we can ask for factory to amend it at once,if the big number we can remark or reject on report and point out of the wrong

作者: cdphz 时间: 2008-1-16 18:05
各位英文都是我学习的榜样！

但是，对于验货，嘿嘿、、、

作者: tyq232 时间: 2008-1-17 13:00
i agree with the view that repoted in the inspecttion report then report the
director,the finial decision should be maked by the buyer.sometime ,if the inspection is in-line,the defect checkde we will asked the factory to advance and rework, as we all know , the key of product of quality control is in- line inspectionnot final inspection

作者: Tony 时间: 2008-3-27 15:50
It's depend on your company which the company is a retailer or an importer or trade industry or the third parts...
For the third parts: remark anything when you found defects. You client will decide it.
For importer ( wholesaler), it no problem for this, but you'd better ask factory correct it. Don't report.
For retailer, ask factory correct it, but don't need to report.
For you, you will ask factory to correct it, after corrected, you should report to HK office. Let them understand you are hard work and careful, responsible...

作者: stephen981 时间: 2008-4-7 11:49
I THINK IT`S VERY EASY TO SOLVE IT,AS A QC I THINK WE DON`T TO FAIL THE GOODS ALL THE PROBLEM,we will to contrue what is matter and what to inprove the prblem ,the supplier can to correct at once,if the problem is easyly to inprove and the supplier can cooperation to correct,when inspection ask for the factory to do it ,i think it will ok.if the problem is dig deal and not correct at once ,you will description all the detail problem on report and telephone to company .

作者: hzm1982_38 时间: 2008-4-7 17:24
As per our PSQS,we do no need report it to the supervisor. Just ask the vendor to correct the shipping mark or reject it.

作者: xiong02299 时间: 2008-4-8 11:20
i'll ask vendor to recorrect it and report to my boss

作者: ericzfr 时间: 2008-4-18 16:01
I have the same opinion as #8 and#9. What is QC's effect or QC's responsibility on site ? And un-expected things occurs during production might be minor or major or critical problems ,so you should take various of correction actions as per result of inspection and shipment of permission in-line or pre-shipment,including communication with factory and related colleague.All what you could do is just to assure the quality of goods.That is no claim for compasation and return/complaint from clients.

作者: catkinglv 时间: 2008-5-1 09:22
i agree with #9,the shipping mark on carton is easily corrected.

作者: JLAAGNSL 时间: 2008-5-11 11:19
Report everything to company if fty could not promise you to correct the things before your leaving.

作者: Billhuang 时间: 2008-7-11 13:03

原帖由 Tony 于 2008-3-27 15:50 发表
It's depend on your company which the company is a retailer or an importer or trade industry or the third parts...
For the third parts: remark anything when you found defects. You client will decide ...

I totally agree with you.

作者: xiaojun98 时间: 2008-7-14 13:14
are you chinese?

作者: cheney850804 时间: 2008-8-12 17:56
It's easy to control things like this,as we are human beings.

作者: wtoqcer 时间: 2008-8-14 21:49
guys: perform in a way that your supervisor would think you are a qualified qc
firstly, always follow the guidlines (both writen or verbal are ok)
secondly, if something out of the guidelines, try to make a judgement just using your common sense and report to your supervisor for a double check. remember, don't never just ask your boss to give an answer, you come up with a proposal to your question and ask if this would be the right way to do.

作者: LZhang 时间: 2008-8-28 22:19
I dont agree to the opions above.I think one should report everything not as request.IF every markings is wrong,it must be corrected.If just a few marking is wrong,it can be accepted.And I think one need not shoulder the responsibility that factory should do.You know if things dont go along with what you are expecting,you will be scolded heavily,even be fired.if you want to keep at your job for a long time,you have to be careful.To be careful!You are responsible for it this time,how about next time?So dont let factory feel it can get chance easily.

作者: 公平竞争 时间: 2008-10-24 17:30
you are all top inspector, but i think we should give relavant parter a clear suggestion

作者: liheng728 时间: 2008-10-25 11:55
i only want to say one word：by yourself

作者: zyq020115 时间: 2008-11-4 23:46
goods may be sent to another port if the shipping mark was wrong. if the correct action under your control, you may let it go, but if not, you must do remark inreport and let the relevant people know of it.

作者: adsl2008 时间: 2008-11-5 14:16
we must check main mark and side mark before inspecting,
Lable mark is wrong ,It is not very big thing, But we must ask supplier to correct it .

作者: marktes 时间: 2009-10-21 23:40
so easy
you mark down in your report , rejcet or pending the goods. send the report to your manager or supervisor.
ask factory rework the shipping mark . before you leave the factory

欢迎光临验货员论坛 (http://bbs.wtoqc.net/)